 Cobalt
and Fuchsia Necklace and Earring Set
This is a fun and colorful necklace
that's sure to please! Although we've listed all the materials we
used, you can vary the design because there really is no pattern.
Just put together the pieces listed and link them together for a fun creation!
Materials:
1 pkg. Capri and Cobalt Two Tone Beads (#24083)
Qty:
1 pkg. Fuchsia 5mm Swarovski Bicones (#16519)
Qty:
1 pkg. S/P Rounds, 3mm (#14030)
Qty:
2 pkg. S/P Tribal Tube Beads (#14542)
Qty:
1 pkg. S/P Bali Style Dots and Circles Beads (#14550)
Qty:
1 pkg. S/P Bali Style Spacer Beads (#14734)
Qty:
1 pkg. S/P Thick Eye Pins, 2 inch (#50116)
Qty:
2 pkg. S/P Thick Eye Pins, 1 inch (#50120)
Qty:
1 pkg. S/P Thick Head Pins, 1 inch (#50104)
Qty:
1 pkg. S/P Jump Rings, 4mm (#50040)
Qty:
1 pkg. S/P Lobster Clasp (#50138)
Qty:
1 pkg. S/P French Hook Ear wires (#50002)
Qty:
Directions:
Step 1:
First we'll make all the sections required for
the necklace and earrings. Again, this is randomly linked together
so you may need to make extra parts as you are stringing along depending
on the look you want.
Onto your 2" eye pins, place one Two Tone bead.
Using a wire cutters, cut off the excess eye pin leaving approximately
3/16". Using a flat nose pliers, bend the 3/16" piece of wire 90°.
Carefully bend the 3/16" piece of wire into a loop, and close it tight.
Repeat this with at least 12 Two Tone beads in varying shapes and sizes.
Use your Bali Style Spacers on the top and bottom of a few of these combinations
( 10 come in a package so you could add these to five of your Two Tone
bead pieces).
Step 2:
Onto your 1" eye pins, place one 3mm S/P Round,
one Bali Style Dots and Circles Beads and one more 3mm S/P Round. Using
a wire cutters, cut off the excess eye pin leaving approximately 3/16".
Using a flat nose pliers, bend the 3/16" piece of wire 90°. Carefully
bend the 3/16" piece of wire into a loop, and close it tight. Repeat
this to make at least 8 pieces total.
Step 3:
Onto your 1" eye pins, place one S/P Tribal Tube
Bead. Using a wire cutters, cut off the excess eye pin leaving approximately
3/16". Using a flat nose pliers, bend the 3/16" piece of wire 90°.
Carefully bend the 3/16" piece of wire into a loop, and close it tight.
Repeat this to make at least 8 pieces total.
Step 4:
Onto your 1" eye pins, place 5mm Fuchsia Swarovski
Bicone. Using a wire cutters, cut off the excess eye pin leaving approximately
3/16". Using a flat nose pliers, bend the 3/16" piece of wire 90°.
Carefully bend the 3/16" piece of wire into a loop, and close it tight.
Repeat this to make at least 14 pieces total.
Step 5:
Onto your 1" head pins, place 5mm Fuchsia Swarovski
Bicone. Using a wire cutters, cut off the excess head pin leaving approximately
3/16". Using a flat nose pliers, bend the 3/16" piece of wire 90°.
Carefully bend the 3/16" piece of wire into a loop, and close it tight.
Repeat this to make at least 3 pieces total.
Step 6:
Onto your 1" head pin, place a Two Tone Bead.
Using a wire cutters, cut off the excess head pin leaving approximately
3/16". Using a flat nose pliers, bend the 3/16" piece of wire 90°.
Carefully bend the 3/16" piece of wire into a loop, and close it tight.
Repeat this to make at least 1 piece.
Step 7:
First we'll assemble the earrings. Take
the pieces from Step 5 and Step 6 to be the ending parts. Open a
jump ring and insert one of the head pin pieces and one of the looped pieces
from the other steps. Repeat until the earring segment is as long
as you'd like it. Attach to the S/P Lever Back ear wire.
Step 8:
Repeat Step 7 for the second piece of your earring
(so you'll have two dangles from the earring). Repeat for the second
earring.
Step 9:
Take your remaining pieces and loop them together
with a jump ring in between each section. Feel free to make more
sections if you need to balance your colors or make the necklace longer.
Attach a clasp to your last eye pin loop or via a jump ring.
|
|
