Jewelry Making Idea: Precious Pearl Bracelet and Earring Set

Precious Pearl Bracelet and Earring Set
This elegant set is made with our Swarovski clear AB crystals and white Swarovski pearls. In between these gorgeous beads are our sterling silver flower link connector charms. You're going to love wearing this set with just about anything. This set would be perfect for a bride as well.

Materials:
1 Pkg. Swarovski Clear AB Crystals, 6mm (#16596) Qty:
1 Pkg. Swarovski White Pearls, 6mm (#26502) Qty:
1 Pkg. S/S Lever Back Earring Findings (#50026) Qty:
1 Pkg. S/S Jump Rings (#50075) Qty:
1 Pkg. S/P Head Pin, 1 inch (#50104) Qty:
1 Pkg. S/P Eye Pin, 1 inch (#50120) Qty:
1 Pkg. Sterling Silver Lobster Claw Clasp (#50134) Qty:
11 Sterling Silver Flower Link Charm (#60900) Qty:
Tools you will need (change quantity to 1 if you need them):
Flat Chain Nose Pliers (#51016) Qty:
Round Nose Pliers (#51017) Qty:
Side Cutters (#51018) Qty:

Directions:
Directions for Bracelet:
Step 1. On each of 3 Eye Pins place a Pearl. Using a Side Cutter cut off the excess Eye Pin leaving approximately 3/16". Using Flat Nose Pliers, bend the 3/16" piece of wire 90°. With the Round Nose Pliers, carefully bend the 3/16" piece of wire into a Loop, but do not close it tightly.   Be sure the Loop you make is facing the same direction as the Loop already on the Eye Pin.
Step 2. Repeat Step 1 but now place a Crystal on each of 3 Eye Pins.

Step 3. Place the Loop of the Link Charm into the open Loop of the Pearl Eye Pin drop you just made. Close the Loop tightly.
Step 4. Repeat Step 3 alternating the Pearl Drops with the Crystal Drops between the Link Charms.
Step 5. Twist open a Jump Ring and place it into the Loop of the last Flower Link Charm on one side of the Bracelet. Twist the Jump Ring closed.
Step 6. Twist open a Jump Ring and place the Loop of the Flower Link Charm and the Loop of the Lobster Claw Clasp. Twist the Jump Ring Closed.

Directions for the Earrings:
Step 1. On each of 2 Head Pins, place a Pearl. Using a Side Cutter cut off the excess Head Pin leaving approximately 3/16". Using Flat Nose Pliers, bend the 3/16" piece of wire 90°. With the Round Nose Pliers, carefully bend the 3/16" piece of wire into a Loop, but do not close it tightly.
Step 2. On each of 2 Eye Pins, place a Crystal. . Using a Side Cutter cut off the excess Eye Pin leaving approximately 3/16". Using Flat Nose Pliers, bend the 3/16" piece of wire 90°. With the Round Nose Pliers, carefully bend the 3/16" piece of wire into a Loop, but do not close it tightly. Be sure the Loop you make is facing the same direction as the Loop already on the Eye Pin.
Step 3. Place the Loop of the Pearl Head Pin Drop you have just made into the Loop of the Link Charm and close the Loop tightly.
Step 4. Now place the open Loop of the Crystal Eye Pin Drop you have just made into the Loop of the other side of the Link Charm and close the Loop tightly.
Step 5. Twist open the other Loop of the Eye Pin and add a Link Charm. Close the Loop tightly.
Step 6. Twist open the Loop on the Earring and place the Loop of the last Link Charm into it and then twist closed tightly. Repeat for second Earring. Enjoy!

Eclectic Etc., Inc. P.O. Box 10 Willow Grove, PA 19090-0010

Phone: 215-658-1711 Toll Free: 1-888-SHOP-ETC
Fax: 215-658-1191
Email: TheHeadBead@eebeads.com

Privacy Policy © Copyright 1996-2008 Eclectic Etc., Inc. All Rights Reserved No part of this page may be reproduced in any manner for commercial or non-commerical purposes without written permission from Eclectic Etc., Inc.