Materials:
1 Pkg. New China Jade Gemstone Rounds, 6mm (#11028-6) Qty: 
1 Pkg. Jonquil Crystals, 6mm (#16109) Qty: 
1 Pkg. Jonquil Druks, 8mm (#22016) Qty: 
1 Pkg. Antique S/S Braid Style Bali Beads, 7X4mm (#27514) Qty: 
1 Pkg. Antique S/S Small Bali Tube Beads, 6X3mm (#27542) Qty: 
1 Pkg. S/P Jump Rings, 4mm (#50040) Qty: 
1 Pkg. 1 1/5" Thin Silver Plated Eye Pins, 24 gauge (#50590) Qty: 
1 Pkg. S/P Filigree Clasps (#50140) Qty: 
5 S/P Space Connectors (#60109) Qty: 
1 Foot of S/S Dot and Dash Oval Chain, 7X4.5mm (#62001) Qty:  
Tools you will need (change quantity to 1 if you need them): 
Flat Chain Nose Pliers (#51016) Qty: 
Round Nose Pliers (#51017) Qty: 
Side Cutters (#51018) Qty: 

Necklace Directions:  When attaching the connectors, we used the short sides.
Step 1. On each of 2 Eye Pins, place a Crystal, a Bali Tube Bead, and a Crystal.  Using Flat Nose Pliers, bend the excess wire 90°.  Make a loop with the excess wire, and close tightly.  Set aside.

Step 2. On each of 2 Eye Pins, place a Druk, a Braid Style Bali Bead, a Gemstone, a Braid Style Bali Bead, and a Druk.  Using Flat Nose Pliers, bend the excess wire 90°.  Make a loop with the excess wire, and close tightly.  Set aside.

Step 3. Twist open a Jump Ring and insert it into to the end of the Chain and one loop of the Clasp.  Twist the Jump Ring closed.  Count past 2 of the larger Ovals of the Chain, which should measure about ½”, and cut the Chain on the next, small Oval.

Step 4. Twist open a Jump Ring and insert the large Oval of the other end of the attached Chain and one Eye Pin Drop that contains Crystals.  Close the Jump Ring.

Step 5.  Twist open a Jump Ring and insert the other end of the attached Eye Pin Drop and the uncut end of the Chain.  Count past 4 of the larger ovals of the Chain, which should measure approximately 1 1/16”.  Cut the chain on the next, small Oval.

Step 6. Twist open a Jump Ring and insert the attached Chain and a Connector.  Twist the Jump ring closed.

Step 7.  Twist open a Jump Ring and insert the other end of the Connector and the uncut Chain.  Twist the Jump Ring closed.  Count past 4 of the larger ovals of the Chain, which should measure approximately 1 1/16”.  Cut the chain on the next, small Oval.

Step 8. Twist open a Jump Ring and insert one of the Eye Pin Drops with the Druks and the attached Chain.  Twist the Jump Ring closed.

Step 9. Repeat Step 5 with the Eye Pin containing the Druks.

Step 10. Repeat Steps 6, 7, 8, and 9

Step 11. Repeat Steps 6 and 7.  Now your third Connector should be attached with Chain hanging from it, to which you will twist open a Jump Ring and insert the attached end of the Chain and the end of the last Eye Pin that contains Crystals.

Step 12. Twist open a Jump Ring and insert the other end of the attached Eye Pin and the uncut end of the Chain.  Count past 2 of the larger ovals of the Chain, which should measure approximately 1/2”.  Cut the chain on the next, small Oval.

Step 13.  Twist open a Jump Ring and insert the end of the Chain and loop of the other side of the Clasp.  Twist the Jump Ring closed.  The necklace is complete and should measure approximately 16 ½”.

Bracelet Directions: 
Step 1. Onto each of 2 Eye Pins, place a Druk and set aside.  Onto each of 2 Eye Pins, place a Crystals and set aside.  Onto each of 2 Eye Pins, place a Gemstone, a Braid Style Bali Bead, and a Gemstone and set aside.

Step 2. Using Flat Nose Pliers, bend the excess wire of each Eye Pin 90°.  Make a loop with the excess wire, and close tightly.  Set all Eye Pins aside.

Step 3. Twist open a Jump Ring and insert one end of the Clasp and one end of a Eye Pin Drop containing Gemstones.  Twist the Jump Ring closed.

Step 4. Twist open a Jump Ring and insert the other end of the Eye Pin Drop with the Gemstone and one end of an Eye Pin Drop with a Crystal.  Twist the Jump Ring closed.

Step 5. Twist open a Jump Ring and insert the other end of the Eye Pin Drop with the Crystal and one end of an Eye Pin Drop with a Druk.  Twist the Jump Ring closed.

Step 6. Twist open a Jump Ring and insert the other end of the Eye Pin Drop with the Druk and a piece of remaining Chain.  Twist the Jump Ring closed.

Step 7. Count past 2 of the larger Ovals of the Chain, which measures about ½” and cut the chain on the next, smaller Oval.

Step 8.  Twist open a Jump Ring and insert the end of the attached Chain and one side of a Connector.  Twist the Jump Ring closed.

Step 9.  Twist open a Jump Ring and insert the other end of the Connector and a piece of the remaining Chain.  Repeat Step 7.

Step 10. Twist open a Jump Ring and insert the other Eye Pin Drop containing Gemstones and the end of the attached Chain.  Twist the Jump Ring closed.

Step 11.  Repeat Steps 4-8.

Step 12.  Twist open a Jump Ring and insert the other end of the Connector and the loop of the other end of the Clasp.  Twist the Jump Ring closed.  The bracelet is complete and the finished length is approximately 7 ¾”.  Enjoy!