Bamboo Jasper Bracelet
The rich patina of our Vintage brass goes so well with our multi colored, earthy tone bamboo jasper rondelles in this bracelet design. To add a splash of color, we added fuchsia 8mm Czech fire polished crystals and 6mm hyacinth crystals. This assymetrical design is sure to please! The braclet fits wrists 7.5 inches around but can be made shorter or longer by changing the length of the chain.

Materials:
1 Pkg. of Bamboo Jasper Rondelle Gemstones (#11879) Qty:
PLEASE NOTE: The Bamboo Jasper Rondelles are gone, but you could substitute ceramic copper rondelles as they are about the same size.
1 Pkg. of Vintage Sunflower Bead Caps (#14075) Qty:
1 Pkg. of Hyacinth Round Fire Polished Crystals, 6mm (#16106) Qty:
1 Pkg. of Fuchsia Round Fire Polished Crystals, 8mm (#16155) Qty:
1 Pkg. of Large Vintage Lobster Claw Clasps (#50325) Qty:
1 Pkg. of Vintage Brass Thick Head Pins, 2”, 20 gauge (#50326) Qty:
1 Pkg. of Vintage Brass Thick Eye Pins, 2”, 20 gauge (#50327) Qty:
1 Pkg. of Solid Copper Antique Jump Rings, 6mm (#50560) Qty:
1 Pkg. of Solid Copper Antique Jump Rings, 8mm (#50323) Qty:
2 Vintage Flying Sparrow Two Hole Connector (#59034) Qty:
1 Foot of Vintage Brass Cable Chain (#62029) Qty:

Tools and glue you will need (change quantity to 1 if you need them):
Flat Chain Nose Pliers (#51016) Qty: 
Round Nose Pliers (#51017) Qty: 
Side Cutters (#51018) Qty: 
Memory Wire Cutters  (#51005) Qty: 

Directions:
Step 1. Cut 3 sections of Chain with a memory wire cutter that will each be 2" long.

Step 2. Twist open an 8mm Jump Ring and insert the link at the end of each section of Chain. Twist the Jump Ring closed. Set aside.

Step 3. Onto each of 10 Head Pins, place a Fuchsia Crystal. We will call these Head Pins A.

Step 4. Using a Side Cutter cut off the excess of each Head Pin leaving approximately 3/16". For each Head Pin, using Flat Nose Pliers, bend the 3/16" piece of wire 90°. Using Round Nose Pliers, bend the 3/16" piece of wire from each Head Pin into a loop and close tightly. Set aside.
Step 5. Onto each of 5 Head Pins, place a Hyacinth Crystal. We will call these Head Pins B.

Step 6. Repeat Step 4 with Head Pins B.

Step 7. Onto each of 4 Eye Pins, place a Bead Cap, a Jasper Rondelle, and a Bead Cap.

Step 8. Repeat Step 4 with these Eye Pins.

Step 9. Twist open a 6mm Jump Ring and insert the links at the opposite ends of your 3 Chain sections (that you attached to the 8mm Jump Ring in Step 2) and the loop of one of your Eye Pins. Twist the Jump Ring closed.

Step 10. Twist open a 6mm Jump Ring and insert the other loop of the Eye Pin that you just attached, 1 of Head Pins A, 1 of Head Pins B, and 1 of Head Pins A, and the loop of another Eye Pin. Twist the Jump Ring closed.

Step 11. Repeat Step 10.

Step 12. Twist open a 6mm Jump Ring and insert the loop at the opposite end of the Eye Pin that you just attached, 1 of Head Pins A, 1 of Head Pins B, 1 of Head Pins A, and a loop from one of your Connectors. Twist the Jump Ring closed.

Step 13. Twist open a 6mm Jump Ring and insert the loop at the opposite end of the Connector that you just attached, 1 of Head Pins A, 1 of Head Pins B, 1 of Head Pins A, and a loop from another one of your Eye Pins. Twist the Jump Ring closed.

Step 14. Repeat Step 12.

Step 15. Twist open another 6mm Jump Ring and insert the loop at the opposite end of your Connector and the loop of a Lobster Clasp. Twist the Jump Ring closed. Enjoy!