Materials:
1 Pkg Light Sapphire Round Fire Polished Crystals, 4mm (#16129) Qty: 
2 Pkg Peridot Graphic Bead (#16768) Qty: 
1 Pkg Gold Plated Jump Rings, 6mm (#50035) Qty: 
1 Pkg Gold Plated Small Toggle Clasps with a Twist in the Bar (#50161) Qty: 
1 Pkg 1 inch Thick Gold Plated Head Pins, 20 gauge (#50583) Qty: 
1 Pkg 2 inch Thick Gold Plated Eye Pins, 24 gauge (#50593) Qty: 
3 Antique Gold Plated Vintage Flying Sparrow Charm (#60514) Qty: 
1 Antique Gold Plated Vintage Soaring 2 Hole Bird (#60522) Qty: 
1 Foot Gold Plated Oval Link Chain (#62016) Qty: 

Tools you will need (change quantity to 1 if you need them): 
Flat Chain Nose Pliers (#51016) Qty: 
Round Nose Pliers (#51017) Qty: 
Side Cutters (#51018) Qty: 
Memory Wire Cutters  (#51005) Qty: 

Directions:
If you want to, you can use a round nose pliers to slightly curve the large soaring 2 hole bird charm to fit around your wrist like we did in the example.

Step 1. Cut a section of Chain that contains 12 links.

Step 2. Twist open a 6mm Jump Ring. Insert the link at one end of the Chain, and insert the loop from the bar end of the Clasp. Twist the Jump Ring closed. Set aside.

Step 3. Onto each of 2 Eye Pins, place a Peridot Graphic Bead.

Step 4. Using a Side Cutter cut off the excess of each Eye Pin leaving approximately 3/16". For each Eye Pin, using Flat Nose Pliers, bend the 3/16" piece of wire 90°. Using Round Nose Pliers, bend the 3/16" piece of wire from each Eye Pin into a loop, and close tightly. Set aside.

Step 5. Onto each of 9 Head Pins, place a Light Sapphire Round Fire Polished Crystal.

Step 6. Using a Side Cutter cut off the excess of each Head Pin leaving approximately ¼ Inch. For each Head Pin, using Flat Nose Pliers, bend the ¼ Inch piece of wire 90°. Using Round Nose Pliers, bend the ¼ Inch piece of wire from each Head Pin into a loop and do not close tightly. Set aside.

Step 7. Twist open a 6mm Jump Ring and insert an Antique Gold Plated Vintage Flying Sparrow Charm. Place the open Jump Ring with the Sparrow Charm onto the 4th link of Chain (counting down from the bar clasp). Twist the Jump Ring closed.

Step 8. On the opposite side of the 4th link of chain, insert the open loop from a Head Pin with a Sapphire Crystal. Close tightly. Repeat this twice more on the same side of the link.

Step 9. Count down three more links to the 7th link. Repeat Steps 7 and 8.

Step 10. Count down three more links to the 10th link. Repeat Steps 7 and 8.

Step 11. Twist open a 6mm Jump Ring, insert the link at the other end of the Chain (on the 12th link), and insert a loop from an Eye Pin with a Peridot Graphic Bead. Twist the Jump Ring closed.

Step 12. Twist open a 6mm Jump Ring and insert the opposite loop from the Eye Pin with Graphic Bead you just attached, and insert a loop from the remaining Eye Pin with Graphic Bead. Twist the Jump Ring closed.

Step 13. Twist open a 6mm Jump Ring and insert the opposite loop from the Eye Pin with Graphic Bead you just attached, and insert loop from the tail end of the Antique Gold Plated Vintage Large Soaring Two Hole Bird Charm. Twist the Jump Ring closed.

Step 14. Twist open a 6mm Jump Ring, insert the opposite loop of the Antique Gold Plated Vintage Large Soaring Two Hole Bird Charm (the loop by the bird’s beak), and the loop from the other side of the clasp. Twist the Jump Ring closed. Enjoy!