Materials:
1 Pkg. New China Jade Teardrops (#11979) Qty: 
1 Pkg. Jonquil Swarovski Crystal Bicones, 4mm (#16542) Qty: 
2 Pkgs. Provence Lavender Xilion Pendant, 8mm (#16790) Qty: 
1 Pkg. Fern Green Xilion Pendant, 6mm (#16791) Qty: 
1 Pkg. Vintage Brass Regular Loop Ear Wires (#50337) Qty: 
1 Pkg. Vintage Brass Swirl Clasp with Ring (#50342) Qty: 
1 Pkg. Vintage Brass 2” Thin Pearl Head Pins (#50346) Qty: 
1 Pkg. Vintage Brass 2” Thin Pearl Eye Pins (#50347) Qty: 
1 Pkg. Solid Copper Jump Rings, 6mm (#50560) Qty: 
2 Vintage Brass Fleur De Lis 2 Hole Drops (#59025) Qty: 
1 Ft. Vintage Brass Medium Oval Cable Chain (#62027) Qty: 

Tools you will need (change quantity to 1 if you need them):
Flat Chain Nose Pliers (#51016) Qty: 
Round Nose Pliers (#51017) Qty: 
Side Cutters (#51018) Qty: 

Directions:
Earring Directions:
Step 1. Take a Head Pin and thread one Jade Teardrop. Form a simple loop above the bead by bending the Head Pin 90 degrees with Flat Nose Pliers and trimming the excess with Side Cutters to leave 3/8 inch behind. Curl into a tight loop with Round Nose Pliers.

Step 2. Gently twist open a Jump Ring and slide it through the loop you made in Step 1. Slide on one Lavender Pendant on each side of the Teardrop..

Step 3. Twist open a Jump Ring and thread on a Fern Pendant. Repeat. Thread them onto the main open Jump Ring underneath the Lavender Pendants and twist them closed. Thread one Jonquil Crystal onto a Head Pin and repeat three more times.

Step 4. Attach the Jonquil Head Pins, two on each side, to the same Jump Ring after forming a simple loop above each bead. Thread the Fleur de Lis Drop onto the Jump Ring and twist it closed.

Step 5. Take an Eye Pin and thread on a Jonquil Crystal. Form a simple above the bead. Pry open the loop on an Ear Wire and thread it through the “eye,” then squeeze closed. Take the other end of the Jonquil Eye Pin and thread that through the other end of the Fleur Drop.

Step 6. Repeat steps 1-5 to complete the other earring.

Bracelet Directions:
Step 1. Cut two pieces of Chain measuring approximately two inches in length each. Also cut two one-link pieces of Chain.

Step 2. Take an Eye Pin and thread on a Jade Teardrop. Repeat two more times and form a simple loop above the bead on each. Take one Teardrop Eye Pin and thread it through the end link on one piece of two inch chain after prying it open. Slide the other end of the Teardrop Eye Pin onto one of the one link pieces of Chain.

Step 3. Take your second Teardrop Eye Pin and thread it onto the one link piece of Chain. Repeat this again with your last Teardrop. Attach the last Teardrop to the other piece of the two inch Chain. Take the Ring from your Clasp and pry it open. Thread it through one end of the Chain and squeeze closed.

Step 5. Create your dangles. Take one Jonquil Crystal and thread onto a Head Pin. Repeat this nine more times and form a simple loop above each bead, then set aside.

Step 6. Pry open a Jump Ring and thread one Lavender Pendant, one Fern Pendant and one Jonquil Head Pin. Repeat this five more times. Set aside.

Step 7. Pry open a Jump Ring and thread on one Jonquil Head Pin, one Lavender Pendant and one Jonquil Head Pin. Repeat this one more time and set aside.

Step 8. Attach the dangles: start from one end of the bracelet. Slide a Jump Ring from Step 6 onto the 3rd link, 6th link and 9th link. Squeeze the Jump Rings closed. Repeat this on the opposite side of the bracelet.

Step 9. Take a Jump Ring from Step 7 and slide through the single link in between the Teardrops. Repeat with the last Jump Ring onto the other single link. Squeeze the Jump Rings closed.

Step 10. Take the opposite end of the Chain and attach the Swirl part of the Clasp by prying open the last link. Twist that link closed. Enjoy!